This blog has moved

This blog is now located at http://wanderlust3.thesailingchannel.tv/.
You will be automatically redirected in 30 seconds, or you may click here.

For feed subscribers, please update your feed subscriptions to
http://wanderlust3.thesailingchannel.tv/feeds/posts/default.

This blog has moved

This blog is now located at http://wanderlust3.thesailingchannel.tv/.
You will be automatically redirected in 30 seconds, or you may click here.

For feed subscribers, please update your feed subscriptions to
http://wanderlust3.thesailingchannel.tv/feeds/posts/default.

Yanmar Engine Self-Repair: Part 2

Here are some details of my Yanmar Engine Self-Repair....
There is a German phrase that is straight to the point; "Wer rastet, der rostet" meaning "He who rests, will rust". I know that with my motorcycles, they are either up hanging from the garage rafters or the frames are up on blocks so my brother can turn over the engines and drive trains every month while they wait patiently for my return. Right: Injector Hole #3.

With my engine, I did NOT do this! When I returned to my favorite anchorage after the Hurricane 'Bill' adventure in the mangroves, I should have run my Yanmar engine a few minutes each week. I did NOT turn it on for 5 weeks and then it seized! Left: Water in #3 Piston.

After the Yanmar technician showed me the sea water in the #3 cylinder, he said it could cost up to $8000 to get it repaired at their Yanmar facility, and would take 3 - 4 weeks. I bought the parts and the Shop Manual, and strarted to 'Do-It-Myself'. First I had to take off all connections - electrical and plumbing.

The Yanmar 4JH4 owner's manual says that after running the engine for prolonged periods at low rpm, before shutting the engine down, you should rev up the engine 5 times to full power and then shut the engine down, to remove carbon build-up in the turbo etc. In my opinion, you still need to let the engine cool down at idle speed a few minutes before you bring it to a stop. My mistake was revving the engine to 2800 or 3000 RPMs for a few seconds five times and then just shutting the engine down. My friend and retired trucker diesel mechanic James, who helped me with the over-haul said you should ALWAYS let the engine idle for 5 or even 10 minutes after running it for a prolonged period, especially the new high speed turbo and ultra high compression 4 valve engines. I did NOT do this, with drastic results.

I learned from my father years ago that when tearing down an engine, you pull off the first things and put each item and its nuts or bolts in a separate container and at the back or end of the work bench, or in this case, a towel lined aft bunk floor. Then you just work clean and organized, labeling or numbering each item with masking tape and a magic marker.

Then I had to lift out the engine from the bilge and onto boards across the sole (floor) to get the engine up to a workable height.
I used a large diameter pipe across the top of the companion way entrance and a borrowed chain hoist.

The engine would not turn over, even with a big leverage bar on the crank-pulley nut. The piston was seized and was soaked in 'Corrosion-X' overnight. But it needed to be drilled and chiseled out.

After taking turns with my friend James at whacking at that piston, then drilling some holes and whacking again, we needed a full day to get that seized piston to finally come loose and pieces removed. I bought a special 'honing' devise to attach to my power drill and we cleaned up and polished the inside cylinder wall according to the Yanmar 'Shop Manual'.

The Yanmar distributor for SE USA, Mastery Engines, was very helpful and especially their service manager, Doug Dykens. He sent me "Everything You Need for an Engine Re-build" including all new seals and gaskets, a new piston and rings, all the little parts for the fuel injectors, and even a special tube of adhesive for the pan gasket. I kept the 'old' piston just as a reminder to check ALL hoses and fittings before a voyage.

Finally, after 7 continuous days of 8 -10 hours work, I was ready to turn her over. James was at the engine and I was at the wheel with the starting key. First tick and she purred like a kitten! Elation and a sense of accomplishment.

After 4 hours of idle speed, I changed the oil and filter. It was a bit dirty and had some diesel fuel mixed in. At ten hours and up to 1800 rpm sailing down to St. thomas and back, I change the oil and filter AGAIN, but it was perfectly clean!

Now, after 25 hours, I hired one of the off-duty Yanmar service technicians to come over to 'WanderLust 3' and check things out and inspect my 're-built' engine, just to make sure I didn't mess anything up. He removed the valve cover and with a feeler gauge checked the tolerances of the valves. They were good. Then he tightened the head bolts with a torque wrench, they were also good. Then a compression check, everything was broken in and running great with 25 hours on the rebuilt engine and two (2) oil and filter changes.

He was slightly impressed that everything seemed to be working perfectly. Then he went to the new Anti-Siphon Valve and also checked the old one. Sure enough the old one was corroded around the rubber flap AND the pressure release tube. This made him think to follow the end of that old tube, re-installed on the new siphon valve. He discovered that the open end, that is supposed to drain and relieve the sea water pressure, was way too long and run under the engine in a cavity that was not visible. When he pulled out the open end of the hose, it was completely CLOGGED with old oil and other debris. That means that eventually the new Anti-Siphon Valve would have FAILED again because the relief tube end was still clogged.

He simply cut that tube, and the parallel one for the generator, about 2 inches above the bilge so it would simply drain down into the bilge AND was also VISIBLE for inspection.

I can only recommend that everyone check the COMPLETE ANTI-SIPHON VALE ASSEMBLY. That maintainance check is NOT in my Hunter Owner's manual nor in the Yanmar book, but it IS in the one essential book I carry from NIGEL Calder, Boat Owner's Mechanical and Electrical Handbook. He devotes five (5) pages (377 -382) to just the subject of "Siphon Breaks". Read it!

Mike Harker
s/v Wanderlust 3

Sailing Documentaries Just $12.99 or Less

Yanmar Engine Self-Repair: Part 1

How can an $80 part cause $8,000 engine damage?

After returning to my favorite spot in the Simpson Bay Lagoon after seeking refuge in the Mullet Pond Mangroves after the only Hurricane (Bill) to be near St. Martin this summer, I did not run the main Yanmar engine for over 7 weeks. That in itself was wrong, I should have run the engine, even for just a few minutes, at least once a week. But with 3 large solar panels and an Air-X wind generator, I only needed to charge my house batteries and make water for about 3 hours a week using the 12 Kw generator.

What I did not know was that the 'Anti-Siphon Valve' at the top of the sea water outlet to cool the intercooler on the Yanmar was corroded and the little flap did not close, allowing sea water back down the hose and into the exhaust, including back through the turbo, exhaust manifold and finally into the open exhaust valve of # 3 cylinder.

The starter would not turn over the engine, so I tried with a 14mm socket to turn the shaft nut at the alternator belt, but no luck. I went over to the Yanmar service facility and the mechanic came out to the boat and took off some hoses and the valve cover to show me how #3 cylinder was filled with sea water.

After e-mailing the Yanmar distributor in Florida, "not a Yanmar part" and the boat manufacturer Hunter, "out of warranty and a maintenance problem not covered under warranty anyway", I asked the service office for a quote. $5000 in cash, in advance, just to have a look at the damage! This would include towing over to their facility, a crane to haul out the engine and 3 - 4 weeks in the shop. If the turbo was damaged and the head and valves needed work the total could be above $8000!!!!

I grew up in Southern California with my Dad and two uncles racing and tuning their race boats. I've seen engines apart at the launch ramp, on an 'All-Night Saturday Night" engine repair before the big race Sunday and enough garage mechanics to attempt the engine over-haul myself. I had the Yanmar 4JH4 HTE service manual and I got Yanmar in Florida to send me all the parts they think I would need, including a new piston and rings, injector tips and all the seals and gaskets for a complete overhaul, and a 'Wish You Luck!".

After getting a steel bar across the companion way and the loan of a small chain hoist, I got the engine up and out of the 'bilge' area and on to boards across the boat's sole. With the stairs removed, I had to enter through the forward hatch. I also got the expertise of a real diesel mechanic, a retired local living on his sailboat for years, JAMES. He has worked on 'many a diesel' including old boat engines and trucks, but never a turbo charged, 4 valve per cylinder modern sailboat engine.

After exactly 1 week we put the hoses back on the engine and fired her back up. She runs perfectly. The turbo was professionally opened and cleaned including new seals and bearings and the head and valves were cleaned and polished. The cylinder wall was honed and polished using a special tool aboard the boat.

For around $800 in parts and about 80 man-hours, we got the engine apart, repaired and back working again. I do NOT recommend that anyone do the same without professional diesel service technicians, but when you are in a desperate situation and need to 'Fix-it-Yourself', it can be done.

I have over 24 hours on the overhauled engine sailing down to St. Thomas and back, I changed the oil and filters twice and the coolant replace a second time and everything works as good as, or, as it seems, better than new.

In Part 2, I'll talk about specific steps during my Yanmar Engine Self-Repair.

Mike Harker
s/v Wanderlust 3

Sailing Documentaries Just $12.99 or Less

MARIGOT: Hurricane Hole

I took this photo from the top of a mast on a boat moored in the 'Pond', back into the little bubble where I was tied to the mangroves with 12 other boats on the Caribbean island of Marigot.

It was a very mixed group. There were a couple from Washington State, another couple from Brazil, and two local sail boats with their masts down on deck with very friendly Dutch couples. There was a German (Steffen, my buddy), a guy from New Zealand, a French guy, and Pips from England.

Check out my location in Google Maps

I also met some great locals I sometimes hung out with. Sinbad was a racing motorcycle specialist and tunes all the best drag bikes. They race every Sunday morning on the highway crossing the Dutch / French border. The cops just watch.

The summer here was very calm and hot. Most of the boats and tourists are gone but the ones that have stayed are all adventuresome. They have at least one hurricane hit each year and the two Dutch boats in our little pond have been through six with two being in the category #5 storms coming out of them with no damage in this "Hurricane Hole".

If I don't get out of the Caribbean this summer into the Pacific, then I will hang out here and visit St. Barts in early November for the 60th birthday celebration at 'Le Select' and visit some other Carib islands before heading back over to the MED in May.

Mike Harker
WanderLust 3

Bitter End Sailing Team

Virgin Gorda, Bitter End Yacht Club - British Virgin Islands

The girls parked their boat on the mooring ball next to me and we all enjoyed 3 days of sailing, activities and parties with live bands on the beach at Virgin Gorda and the 'Bitter End Yacht Club.

Mike Harker
s/v Wanderlust3

Sailing Documentaries Just $12.99 or Less

YachtBlast "Island 92" Radio: Mike Harker Interview

Gaz

During the 2009 Heineken Regatta, Mike was interviewed by Gaz, host of YachtBlast on Island 92 radio, Simpson Bay, St. Maarteen N.A. Mike discusses his early hang gliding career, his near-life-ending accident, how he got into sailing, his recent circumnavigation, and his future sailing plans. Check out more YachtBlast podcasts.

HARKER INTERVIEW

Sailing Documentaries just $12.99 or Less